Close

Search:

Type: Posts; User: all4bspinnin

Page 1 of 8 1 2 3 4

Search: Search took 0.00 seconds.

  1. Replies
    1,138
    Views
    483,304

    Yea, thats ok

    Yea, thats ok
  2. Replies
    1,138
    Views
    483,304

    KA VA LAN is without a doubt one of the best...

    KA VA LAN is without a doubt one of the best whiskeys ive ever had. If i could find it here in florida, its the only whisky id ever buy again.
  3. N54: Yea, for sure. While I dont run Jb4 on any of my...

    Yea, for sure. While I dont run Jb4 on any of my stuff, as a piggy back boost controller, it works pretty well on the N54's and the pi control is useful. I still like the stock ECU better but Terry...
  4. N54: This shop is here in Jacksonville. I think Shawn...

    This shop is here in Jacksonville. I think Shawn f'd up pretty bad going after JB4 in a video. It wouldnt surprise me if he got a cease and desist letter from Burger Motorsports lol

    I think him...
  5. Replies
    927
    Views
    174,188

    N54: look for the pre-control a table. Make the cells...

    look for the pre-control a table. Make the cells in the top left corner 0 (the ones that are set to 11). Also, on the wastegate base table, you can try setting the top left value to 0 as well. ...
  6. Replies
    927
    Views
    174,188

    N54: You dont really need it to be honest. You can...

    You dont really need it to be honest. You can rebuild the stock table like an RPM x SP table with similar results
  7. N54: Thanks Chris.

    Thanks Chris.
  8. N54: VTT, just curious why the coupler on the outlet...

    VTT, just curious why the coupler on the outlet is in that spot instead of closer to the rear turbo where its father away from the manifold? Im sure theres a reason, I figured id ask though.
  9. Replies
    927
    Views
    174,188

    N54: rpm x setpoint does not use pre-control A. ...

    rpm x setpoint does not use pre-control A. remember, set your wgdc floor to 0. the value in the rpm x sp table is wgdc applied after spring pressure.

    Are you trying to use rpm x sp to fix the...
  10. N54: I agree with Sticky on continuing development for...

    I agree with Sticky on continuing development for BB and supporting Trevor.

    With Jake being the only one doing development for the community it puts a huge strain on him and doesnt help the...
  11. N54: trevorlee02 PM'd

    trevorlee02 PM'd
  12. Replies
    36
    Views
    5,404

    N54: Ambient temp was in the low 80's in Ocala...

    Ambient temp was in the low 80's in Ocala florida. If your goals are 650 or less, its a great intercooler.
  13. Replies
    36
    Views
    5,404

    N54: we went 156 in the half mile with the ATM...

    we went 156 in the half mile with the ATM intercooler. It works amazingly well. Hell, id put that intercooler up against anything on the market for an N54.
  14. N54: ^^this

    ^^this
  15. N54: Brad, I was looking at that table recently and...

    Brad, I was looking at that table recently and saw the 80nm you're referring to. If you try it, lmk how it goes. Ideally a slow ramp rate back to the timing from the Timing (main) for that load/rpm...
  16. N54: You are magician Jake. Quit trying to hide it. ...

    You are magician Jake. Quit trying to hide it.

    I'm just being a brat and being impatient. As long as you promise you'll release them I'm good and I'll shut up.

    Thank you guys as always...
  17. N54: Sticky Its been that way for a while now. Motiv...

    Sticky Its been that way for a while now. Motiv has an XDF with rolling anti lag, EGT, flex fuel and a host of other goodies that are not on the public XDF. MHD also has given them F series...
  18. N54: Brad, I had a conversation with Clemens @ xHP...

    Brad, I had a conversation with Clemens @ xHP about the torque re-introduction. He knew what tables to modify but would not release them to me as they are not a part of the xdf. Would you happen to...
  19. N54: Keep going on the table discovery. I appreciate...

    Keep going on the table discovery. I appreciate the efforts of both you and jyamona!
  20. N54: I havent seen any with an ebp reading. Just dyno...

    I havent seen any with an ebp reading. Just dyno pulls with changes showing power increases/better spool
  21. Replies
    1
    Views
    1,238

    You are amazing. keep it up dzenno!! awesome...

    You are amazing. keep it up dzenno!! awesome stuff
  22. Replies
    13
    Views
    3,685

    N54: Tec, the spreadsheet gives the basics so its a...

    Tec, the spreadsheet gives the basics so its a great start but there's much much more to understand. Take some time and watch a few videos on youtube about p.i.d boost tuning. Motec's youtube...
  23. Replies
    5
    Views
    18,708

    Is this spec race car an n54? or is this a...

    Is this spec race car an n54? or is this a naturally aspirated bmw of some kind? e85 has a slower flame speed than gas so NA cars dont really see much of a gain until you bump the compression up. ...
  24. Replies
    2
    Views
    670

    N54: Your question is a bit vague but im going to give...

    Your question is a bit vague but im going to give answering it a shot.

    A single turbo car is going to build boost differently. The stock load/rpm axis's are designed for stock turbo cars that...
  25. Replies
    4
    Views
    1,019

    N54: exactly. Usually with lean spool you have to be...

    exactly. Usually with lean spool you have to be very careful. i personally wouldnt even touch it unless I was on e85. You can do the same lean spool tuning yourself using the tables you've posted....
Results 1 to 25 of 177
Page 1 of 8 1 2 3 4