Close

    • 430 horsepower and 369 pound-feet of torque for 2014 F80 M3 / F82 M4 S55 twin turbo motor - Curb weight of 3306 pounds, manual transmission

      Finally some concrete details from BMW on the next generation M3/M4! What may be interpreted as bad news is the horsepower output from the 3.0 liter inline-6 S55 twin turbo (single scroll turbo) motor is 'only' 430 horses. The torque figure is at 369 pound-feet. Not exactly a powerhouse of a motor or a torque monster but the good news is that this powerplant is mated to a chassis that will weigh about 3306 pounds or 1500 kilograms.

      A curb weight of 3306 pounds makes the F80 M3 / F82 M4 lighter than both previous generation M3 vehicles the E46 and E9X. It seems AutoBild got the specifications correct for the most part when they leaked them last month although horsepower is up from their claimed 416. If BMW does a Competition Package with the new M3 (chances are they will as fanboys will raise hell about the C63 out-muscling the M3 and the tiny increase over the E9X) the power, curb weight, torque, and dual clutch transmission will make for a package likely capable of high 11's in the 1/4 mile out of the box.

      What is the redline of the motor? A good question. BMW has not officially confirmed the redline although they claim the new motor is high revving. Keep in mind BMW also made this claim about the S63TU V8 under the hood of the M5 and M aficionados hardly refer to that stump puller as a high revver.

      AutoBild claimed 7800 rpm although that may be overly optimistic. Current reports place the redline somewhere between 7500 to 7800 rpm. BMW has yet to confirm the exact number but says it is 'over 7500 rpm.' How much over they do not say.

      The motor has a closed deck design meaning it is not based on the N54 as some people speculated (N54 fanboys). The motor does have Valvetronic. The block is seemingly a brand new design. The power is sent to a carbon fiber driveshaft.

      BMW also confirmed the manual transmission option meaning Autoblog F'd up royally with their report stating the M3/M4 would not have a manual transmission. Further details to come but what is concrete as of right now are the horsepower, torque, transmission, and curb weight figures. Additionally, both the sedan and the coupe will have carbon fiber roofs. BMW press release and photos below.












































































      1. The new BMW M3 Sedan and new BMW M4 Coupe:
      Innovative engine technology and a focus on lightweight design.


      The launch of the new BMW M3 Sedan and new BMW M4 Coupe sees BMW M GmbH revealing an all-new interpretation of the high-performance sports car – and carrying the BMW M philosophy over into the fifth generation of the M3. More than 40,000 examples of the fourth-generation BMW M3 Coupe were built, and now the BMW M4 Coupe is poised to continue this history of success. The "M4" badge is a reference to the model series that provides the basis for the new M model. And for the first time, the Coupe will be introduced at the same time as the four-door variant, which logic dictates will be christened the BMW M3.

      "Four generations of the BMW M3 have blended motor sport genes and uncompromised everyday usability within an emotionally rich overall concept;" explains Dr Friedrich Nitschke, President BMW M GmbH. "The BMW M3 Sedan and BMW M4 Coupe represent an ongoing commitment to this philosophy. The engine is the heart of every M model, and the example fitted in the two new cars combines the virtues of a high-revving naturally aspirated unit with the strengths of turbocharger technology. An all-embracing lightweight design concept keeps the cars' weight to just under 1,500 kilograms. The BMW M3 and BMW M4 take motor sport technology from the track to the road, and thousands of laps of the legendary Nürburgring Nordschleife – the world's most demanding race track – have readied the new models for that transition. Meticulous and passion-fuelled development work has underpinned the creation of two high-performance sports cars that set new standards in terms of overall concept, precision and agility."

      The high-revving six-cylinder in-line engine with BMW M TwinPower Turbo technology newly developed for the new BMW M3 Sedan and BMW M4 Coupe produces maximum output of approximately 430 hp. Its peak torque soars far beyond 500 Newton metres (369 lb-ft), outstripping the figures recorded by the outgoing BMW M3 by well over 30 per cent. And yet the engine also achieves a reduction in fuel consumption and emissions of around 25 per cent. The weight of the cars has been reduced to just under 1,500 kilograms, which helps to ensure outstanding driving dynamics and exceptional efficiency.

      2. The balance of the overall concept:
      A blend of elements working in perfect harmony delivers outstanding performance, precision and agility.


      The new BMW M3 Sedan and new BMW M4 Coupe share a low-slung and broad-set, yet finely balanced, stance on the road, highlighting the emphasis on performance capability in the emotional development of M design. Large air intakes at the front end, exposed carbon-fibre-reinforced plastic (CFRP) components and the diffuser at the muscular rear end are far from mere design flourishes; they also fulfil functional roles in terms of aerodynamics, cooling and weight saving.

      Numerous aerodynamics measures integrated into all areas of the body.
      The aerodynamics concept of BMW M GmbH models has always been one of the key elements in their development. The engineers need to channel the air around the car to create the best possible platform for dynamic excellence, while also ensuring the engine, powertrain and brakes receive the requisite cooling given the significant loads they are operating under. But at the same time, the cars should also have a good Cd – an indicator of impressive efficiency at higher speeds, in particular.

      Details such as the powerfully formed front apron, smooth underbody and clearly defined Gurney spoiler lip at the rear of the M3 Sedan (or integrated spoiler lip at the rear of the BMW M4 Coupe) reduce lift by an equal degree at the front and rear axle and produce optimum handling attributes. These examples underline in familiar fashion the success of M engineers in reconciling the requirements of everyday use with the demands of action on the race track. Elements like the Air Curtain and M gills with integrated Air Breather rearwards of the front wheels minimise turbulence in the front wheel arches. And, together with the smoothly sculpted exterior mirrors, they are also highly distinctive design features of the BMW M3 Sedan and BMW M4 Coupe.

      Sophisticated cooling concept for maximum performance.
      The exceptional performance potential of the BMW M3 Sedan and BMW M4 Coupe places extremely exacting demands on temperature management in the engine and peripheral assemblies. In order to ensure optimum operating temperatures in everyday use, on short journeys around town and on the race track, the BMW M GmbH engineers have developed an extremely effective cooling system. For example, alongside the two ultra-dynamic turbocharger units, the air intake system of the six-cylinder engine also includes an indirect intercooler to cool the intake air, maximising charge pressure and engine output. As well as a main radiator, the track-ready cooling concept also comprises additional radiators for the high- and low-temperature water circuits, turbocharger and transmission oil. These ensure a consistent temperature balance and therefore unrestricted performance during hard driving. An additional electric coolant pump cools the turbocharger bearing mounts when the car is stationary.

      The powertrain gains from a wide variety of motor sport technologies.
      The many years of experience in motor sport clocked up by the BMW M engineers also make their presence felt in the construction of the powertrain for the new BMW M3 Sedan and BMW M4 Coupe. For example, the engine's impressive torque is sent on its way by a forged crankshaft with high torsional rigidity, whose low weight also allows a significant reduction in rotating mass. The crankshaft therefore helps to optimise the engine's responsiveness and acceleration and makes an important contribution to its high-revving character.

      The engine sends its power to the wheels through a six-speed manual gearbox as standard. This gearbox is significantly more compact than its predecessor and 12 kilograms lighter, allowing it to assist the car's optimum – virtually 50:50 – weight distribution. As a means of increasing shift comfort, the manual gearbox uses innovative new carbon friction linings in its synchroniser rings. Dry sump lubrication provides an efficient supply of oil to all parts of the gearbox. The new gearbox also works a lot more quietly than before and blips the throttle on downshifts – previously a feature reserved for the M Double Clutch Transmission. This engagement speed control function helps to enhance stability and was originally developed by motor sport engineers.

      Seven-speed M Double Clutch Transmission with Launch Control.
      The optional seven-speed M Double Clutch Transmission with DriveLogic takes a very special route to combining the apparently conflicting values of absolute sports performance and comfort. As well as changing gear automatically, in manual mode the transmission enables ultra-fast gear changes with no interruption in the flow of power. The integrated Launch Control function ensures optimum sprinting performance off the line, producing acceleration figures that would be out of range with the manual gearbox. The M Double Clutch Transmission also offers drivers extra functions, such as selectable modes which make the BMW M3 and BMW M4 more comfortable, easier on fuel or even sportier. The extra gear over the manual gearbox allows more tightly spaced ratios – and delivers the positive effects on performance and efficiency you would expect as a result.

      The material properties of carbon have allowed the engineers to follow a fundamentally new approach in the manufacture of the drive shaft. This component feeds the engine's torque from the gearbox to the rear differential and works under extremely heavy loads – especially in high-performance vehicles. The impressive stiffness and low weight of CFRP as a material allow the drive shaft to be constructed as a single-piece unit with no centre bearing. As well as a weight saving of 40 per cent over its predecessor, this leads to a reduction in rotating masses and, in turn, to sharper responses to movements of the accelerator, combined with enhanced dynamics.

      Another feature that adds fresh polish to the dynamic repertoire of the BMW M3 Sedan and BMW M4 Coupe is the Active M Differential. Unlike the manual system used by the outgoing BMW M3, here an electric actuator constantly varies the locking effect, as required. That enables better traction, the adjustability of the car is improved, and understeer coming out of corners is dialled out to impressive effect. M Dynamic Mode – a subfunction of the Dynamic Stability Control (DSC) system – quenches the thirst of enthusiastic drivers for keen dynamics. While DSC intervenes as required to counteract understeer and oversteer, M Dynamic Mode allows greater wheel slip and therefore easy drifting. Owners with a taste for sporty and dynamic driving will appreciate this breadth to the cars' handling, although DSC will still step in if the car ventures over the limits – unless it is switched off completely. Whichever setting the driver chooses, he or she remains responsible for the car's stability.

      Aluminium suspension elements ensure sharper dynamics.
      The core expertise of BMW M GmbH resides in creating cars that offer impressive steering precision, on-the-limit adjustability, agility and driving feeling, together with unbeatable traction and outstanding directional stability – all without neglecting everyday usability. In order to blend these attributes with the significantly increased performance capability of the new BMW M3 Sedan and new BMW M4 Coupe, the axles of the outgoing BMW M3 have undergone further development and all relevant components have been newly designed or constructed.

      Here again, low weight and a high level of structural rigidity are essential ingredients in ensuring the cars provide an ultra-dynamic driving experience. In the double-joint spring strut front axle alone, the use of a lightweight aluminium construction for components such as control arms, wheel carriers and axle subframes saves five kilograms over a conventional steel design.

      Play-free ball joints and elastomer bearings developed specially for the BMW M3 Sedan and BMW M4 Coupe ensure an optimum and direct transfer of forces both laterally and longitudinally. An aluminium stiffening plate, CFRP front strut brace and additional bolted joints between the axle subframe and the body sills all help to increase the rigidity of the front structure.

      Also lighter than the construction in the outgoing BMW M3 is the new five- link rear axle. All the control arms and wheel carriers are manufactured using forged aluminium, which reduces the unsprung masses of the wheel-locating components by around three kilograms compared with the previous model generation. The rigid connection between the rear axle subframe and the body – without the use of elastic rubber elements – is borrowed from motor sport and serves to further improve wheel location and therefore directional stability.

      The development of the tyres for the cars was incorporated from the outset into the construction process for the axles. For high-performance sports cars like the BMW M3 Sedan and BMW M4 Coupe, in particular, steering feel and precision are the foremost considerations in the development of tyres for the front axle, alongside lateral stability and braking forces. At the rear axle, meanwhile, traction, lateral stability and directional stability take centre stage. For this reason, both cars will leave the factory on low-weight forged wheels with mixed-size tyres. The specially developed forged wheels make a significant contribution to the reduction in the cars' unsprung masses and, in turn, to the optimisation of dynamic qualities and efficiency.

      Electric Power Steering with three settings.
      The electromechanical steering system used in the BMW M3 Sedan and BMW M4 Coupe is a new development from BMW M GmbH. It has been tuned specially to assist the cause of dynamic driving and offers the gifts of direct steering feeling and precise feedback. The integrated Servotronic function electronically adjusts the level of steering assistance according to the car's speed, providing optimum steering characteristics at all speeds. The steering for the BMW M3 Sedan and BMW M4 Coupe also offers the driver three steering characteristics as standard, which can be selected at the touch of a button. COMFORT, SPORT and SPORT+ modes allow the level of steering assistance to be adapted to suit the situation at hand and the driver's personal tastes.

      The optional Adaptive M suspension likewise comes with COMFORT, SPORT and SPORT+ modes, enabling the driver to choose between a more comfortable damper setting for motorway driving, for example, a stiffer set-up for dynamic driving on country roads, and a third option that minimises wheel movements and maximises dynamic performance for use on the track.

      With their supreme dynamic attributes in mind, the BMW M3 Sedan and BMW M4 Coupe also come as standard with BMW M compound brakes boasting impressive feel, outstanding stopping power and high resistance to fade. Far lighter than conventional equivalents, these brakes contribute to a substantial reduction in unsprung masses and therefore help to enhance dynamic performance. Even lighter BMW M carbon ceramic brakes can also be specified as an option, their further optimised performance attributes equipping them even more effectively for track use.

      3. New six-cylinder in-line engine:
      High-revving, turbocharged engine combines the best of both worlds.


      The new BMW M3 Sedan and new BMW M4 Coupe from BMW M GmbH see a return to a six-in-line engine configuration, as used on the second and third generations of this iconic sports car. The new turbocharged unit, which can develop more than 7,500 rpm, combines the best of both worlds – on the one hand a high-revving design for instant response, linear power delivery over a wide engine speed range and an unmistakable and characterful engine note, and on the other hand BMW TwinPower Turbo technology for maximised torque over a broad rpm range. A further hallmark of this engine is its outstanding efficiency.

      The new engine sees a slight power upgrade over the previous V8 to approximately 430 hp, while peak torque has been increased by well over 30 per cent to substantially more than 500 Newton metres, and is maintained over a very wide rev band. The new powerplant also boasts excellent fuel consumption, with an improvement of more than 25 per cent over the previous model's figures, while emissions are already EU6-compliant.

      The BMW M TwinPower Turbo technology comprises two mono-scroll turbochargers, High Precision Direct Injection, VALVETRONIC variable valve timing and Double-VANOS seamlessly variable camshaft timing. The variable valve and camshaft timing provide fully variable control of intake valve lift. This allows the engine to deliver its power smoothly and efficiently, resulting in lower fuel consumption and emissions. At the same time, throttle response is even sharper than before.

      The six-cylinder engine features a closed-deck crankcase design, which increases rigidity and allows cylinder pressures to be increased for maximised power output. And instead of liners, the cylinder bores feature a twin-wire arc-sprayed coating, which results in a significant reduction in engine weight.

      A further technical highlight is the forged, torsionally rigid crankshaft which, as well as providing increased torque-carrying capacity, is also lighter in weight. Its reduced rotating masses also improve throttle response and acceleration.

      Track-ready cooling system and engine oil supply for outstanding performance.
      The exceptional performance of the BMW M3 Sedan and BMW M4 Coupe also demands an exceptionally sophisticated thermal management system for the engine and ancillary units. To ensure optimal operating temperatures both in short everyday trips around town and also when the vehicle is being driven flat out on the track, the M GmbH engineers developed a highly efficient cooling system, comprising a main radiator plus additional radiators for the high- and low-temperature circuits, turbocharger and transmission, while a temperature-stabilising electric water pump ensures that the engine can develop its full performance at all times.

      The engine oil supply system, too, reflects the extensive motor sport experience of BMW M GmbH. The low-weight magnesium oil sump, for example, features a special cover to limit movement of the oil under the effects of strong dynamic lateral acceleration. Under extreme longitudinal acceleration and deceleration, an oil extraction pump and a sophisticated oil return system situated close to the turbocharger likewise help to maintain uninterrupted oil circulation. Oil is therefore supplied continuously to all engine components in all driving situations – whether in everyday motoring or during hard driving on the track.

      An engine sound in keeping with the motor sport-level performance of the BMW M3 and BMW M4 is provided by an innovative flap arrangement in the twin-pipe exhaust system. The electrically controlled flaps just before the rear silencer minimise exhaust back-pressure and produce a BMW M sound which is striking and unmistakable over the entire engine speed range, as well as giving precise feedback on engine load.

      Intelligent lightweight design was a top priority in the development of the BMW M3 and BMW M4. The goal was to minimise kerb weight in order to give both models outstanding driving dynamics and exemplary efficiency. These measures have delivered impressive results. The kerb weight of the BMW M4 has been reduced to less than 1,500 kilograms, which means the new model is now around 80 kilograms lighter than a comparably equipped predecessor model – with benefits for driving dynamics and fuel consumption as well.

      BMW M3 Sedan also gets CFRP roof for first the time.
      On the outgoing models, the CFRP roof was confined to the Coupe version. Now, for the first time, the four-door BMW M3 will also include this striking design and functional feature. The CFRP roof brings weight savings of five kilograms in the case of the BMW M3 Sedan and more than six in the case of the BMW M4 Coupe. It also lowers the vehicle's centre of gravity, which has a positive impact on driving dynamics.

      On the M4 Coupe, the contoured roofline with the central Gurney bubble continues into the boot lid, and emphasises the even sportier personality of the new model. The newly developed boot lid of this model not only provides extremely effective tail end styling but at the same time its geometry is precisely tailored for optimised aerodynamics, while the use of carbon fibre and plastics provides additional weight savings.

      The new BMW M3 Sedan and new BMW M4 Coupe also feature a CFRP propeller shaft. CFRP's high rigidity and low weight mean that the drive shaft can be produced as a single-piece component without a centre bearing. This provides 40 per cent weight savings over the previous model, and the reduction in rotating masses results in sharper throttle response. The use of carbon in these models is a reminder that BMW is a global leader in high- strength, lightweight CFRP construction, and that it was BMW who brought out the first mass-production vehicle with a body consisting entirely of this material – the innovative BMW i3.

      The CFRP strut brace in the engine compartment is a further example of how all weight-saving measures on these vehicles have also been tailored to the improvement of driving dynamics. Weighing only 1.5 kilograms, the strut brace offers superior rigidity to a comparable aluminium component, and plays a key part in the excellent steering response and precision of both vehicles.

      5. DTM support for the development process:
      Testing at the Nürburgring with Bruno Spengler and Timo Glock.


      In the development of the new BMW M3 Sedan and new BMW M4 Coupe, the BMW M engineers could count not only on track-honed technologies, but also on the driving talent of experienced racers. For example, BMW works drivers Bruno Spengler and Timo Glock took part in extensive testing and set- up runs on the Nürburgring-Nordschleife circuit, focusing on assessment of the cars' suspension, tyres and all elements of the powertrain. After taking the prototypes for a run-out over the legendary and highly demanding circuit, the two professional racing drivers were able to give the BMW M development team some valuable feedback.

      "I'm proud to have made a contribution to the set-up work on these two cars," explained reigning DTM champion Spengler. "The development work may not be totally completed yet, but the driving experience is already sensational. The suspension has a very sporty set-up, the feedback from the front axle is extremely direct and the grip at the rear axle is phenomenal. The engine is impressive, too. The power is right there, even at low rpm, and you can sense that you'll be able to access the output and torque over an extremely wide rev band. I'm looking forward to driving the cars again, but I'm even more excited about driving my first laps in a BMW M4 DTM."

      Timo Glock was similarly impressed: "These two cars are capable of generating quite incredible centrifugal forces," reported the ex-Formula One driver.
      This article was originally published in forum thread: 430 horsepower and 369 pound-feet of torque for F80 M3 / F82 M4 S55 twin turbo motor - Curb weight of of 3306 pounds, manual transmission started by Sticky View original post
      Comments 251 Comments
      1. Sticky's Avatar
        Sticky -
        Click here to enlarge Originally Posted by lulz_m3 Click here to enlarge
        Because efficiency leads to higher performance. You have to keep pushing the boundary of the system until its able to support wherever you are trying to take it. If they just ditched DI, it will never get better. Remember how $#@!ty fuel injection used to be back in the day? Should we go back to carburetors now?
        No it doesn't. It's an efficiency technology that allows cars to run leaner for MPG gains. Also higher compression on pump gas before detonation. Keywords being pump gas.

        Why then did BMW introduce it on their pedestrian motors when it was notably absent from their high performance M motors?

        If it led to higher performance why is the N54 struggling while the S65 is breaking records?

        Nobody is saying go back to carburetors your point is the equivalent of saying let's ditch modern cars for horse drawn buggies, not applicable.

        Weird the vast majority of racing series' don't use direct injection...
      1. Sticky's Avatar
        Sticky -
        Click here to enlarge Originally Posted by Autobahn335i Click here to enlarge
        I don't think BMW has implanted a dry sump system on any production engine EVER .
        That does not mean they could not have started finally.
      1. Autobahn335i's Avatar
        Autobahn335i -
        Click here to enlarge Originally Posted by Sticky Click here to enlarge
        That does not mean they could not have started finally.
        How many engines have been lost due to oil starvation?
      1. Sticky's Avatar
        Sticky -
        Click here to enlarge Originally Posted by Autobahn335i Click here to enlarge
        How many engines have been lost due to oil starvation?
        Let me check the list I keep under my pillow detailing every motor in every M car ever lost to oil starvation. Hold on.
      1. spool twice's Avatar
        spool twice -
        Click here to enlarge Originally Posted by inlineS54B32 Click here to enlarge
        Yeah, that's what their release said too:

        The i-6, internally called S55, is the heart of the new car; Norbert Siegl, who was responsible for the development of the all-aluminum powerhouse, maintains that it is essentially a new unit - even though he started out with the BMW AG's N55. The 3.0-liter inline-six will make slightly over 420 horsepower and "far beyond 369 lb-ft," BMW says. Our educated guess is that it will make around 390 lb-ft. The engine is boosted by two relatively small Mitsubishi turbochargers which provide up to 18.1 PSI. (BMW disingeniously sticks to the "Twin Power" designation, which signifies little. The same moniker is stuck to the single-turbo N55 engine.). There is an electromechanical wastegate and a large intercooler, which sits atop the engine - and which is the reason for the massive bulge on the M3/M4's aluminum hood.

        According to my calculations:

        If the car is making 430HP between 5,000-7,000rpm, it needs to at least be making:

        451.50 ft/tq @ 5,000rpm
        376.25 ft/tq @ 6,000rpm
        322.50 ft/tq @ 7,000rpm
      1. Sticky's Avatar
        Sticky -
        Click here to enlarge Originally Posted by cstavaru Click here to enlarge
        It just doesn't matter whether it is V8 or a six-cylinder if they have the same capacity.

        And when they say "it's the most...in it's class" this is just marketing, because in a "class" they can put any restrictions they want: "high-performance, over 600hp, V8, non-direct-injected, etc." Basically they can create the "class" to include only the engine they are talking about, and then for sure it will be the first in class Click here to enlarge

        And to further realize what direct injection can bring to the table, just compare the 263g/km emissions of the e92 M3 with the 232g/km of the F10 M5 (which has 10% more capacity !).

        Another example: the BMW 330i from 2006, which is naturally aspirated without direct injection, has a city fuel consumption of 12.7l/100km , while the 330i from 2008, which has direct injection, has a city fuel consumption of 10l/100km.

        There is just no point in denying the advantages of direct injection.
        It does matter if it's a V8 or six-cylinder because my point specifically mentioned high-performance V8 not just any motor you can throw out there. You then provided a six-cylinder. What 600+ horsepower V8 is cleaner than the McLaren's? Is the GT500's?

        Class is marketing? Seems to me the McLaren is in a over $200k+ sports car class so you are comparing it to what? Everything out there? That doesn't make any sense it should be compared to other cars in that class which the Porsche 911 Turbo is simply not in. The 458 Italia and Gallardo would be more in that class don't you think?

        I'm not saying direct injection does not have efficiency advantages. I'm saying you don't need it as the McLaren MP4-12C demonstrates which was the entire point and it has a VERY clean motor. And engineering awards support this point do they not? Clearly direct injection also has disadvantages when it comes to performance hence why it is primarily used as an efficiency technology and why McLaren omitted it. BMW M also omitted it in their naturally aspirated M motors. I don't want it in my high performance motor. If you want to save the polar bears or save a couple bucks on gas go for it.

        There is no denying the disadvantages of direct injection.
      1. ezec63's Avatar
        ezec63 -
        Click here to enlarge Originally Posted by Sticky Click here to enlarge
        Benz has sat quietly thus far.

        We know they will have a 4.0 liter V8. We know it will have more muscle.

        All wheel drive plus DCT should make the straightline game in the C63's favor but what will it weigh? It's supposed to be lighter than the previous gen W204.

        So then BMW will release a Competition Package to make it even and then Mercedes can regain their lead with a P31 pack.
        Yupp they havent released much info on it but you can be sure in typical AMG fashion it will be a monster ! Same motor will be in the SLC and capable of almost 600hp which im sure is mostly software so their should be alot of potential in that motor. No doubt the AMG will be the straightline winner with 2 more cylinders and 33% more displacement coupled with AWD and finally a true DCT. They have stated it will deff be lighter than the current c63 but I doubt it will be close to 3300 BMW hit a home run with the curb weight on this car. Honestly im not the biggest fan of AWD sure its good for stoplight races but the control,feel, and excitement of RWD is on another level for me. I had a X6 before my c63 and loved it for a truck if benz doesnt offer RWD on the next C63 or C55 I have a good feeling ill be sitting in a alpine white m4.
      1. Autobahn335i's Avatar
        Autobahn335i -
        Click here to enlarge Originally Posted by Sticky Click here to enlarge
        Let me check the list I keep under my pillow detailing every motor in every M car ever lost to oil starvation. Hold on.
        See, surely much less than to, let's say rod bearing issues. It's understandable that BMW does not make this a top priority. Although it surely would be nice. Maybe it will be in the next M1 (if it ever comes) with a proper M race engine.

        The F82 M4 is plenty fast around the track as is. Word is the Ring time is 7:38. Compare that to the 7:48 of the E92 M3 GTS!
      1. lulz_m3's Avatar
        lulz_m3 -
        Click here to enlarge Originally Posted by Sticky Click here to enlarge
        No it doesn't. It's an efficiency technology that allows cars to run leaner for MPG gains. Also higher compression on pump gas before detonation. Keywords being pump gas.

        Why then did BMW introduce it on their pedestrian motors when it was notably absent from their high performance M motors?

        If it led to higher performance why is the N54 struggling while the S65 is breaking records?

        Nobody is saying go back to carburetors your point is the equivalent of saying let's ditch modern cars for horse drawn buggies, not applicable.

        Weird the vast majority of racing series' don't use direct injection...

        I would argue that anything that is high performance must also be high efficiency. You say DI only offers advantages on pump gas, its actually much more advantageous on ethanol as the cooling effect is multiplied vs normal PI of ethanol. Direct injection is not going anywhere, and i'm willing to bet it will trickle its way into race cars over the next 10 years.
      1. BlackJetE90OC's Avatar
        BlackJetE90OC -
        Click here to enlarge Originally Posted by Sticky Click here to enlarge
        Let me check the list I keep under my pillow detailing every motor in every M car ever lost to oil starvation. Hold on.
        Actually think the S65 is prone to oil starvation. Some of the failures I have seen first hand at track days have to be related. Just recently saw a DCT M3 with only about 10k miles blow up at COTA. There is a couple turns with extended lateral g's.
      1. Group.america's Avatar
        Group.america -
        Click here to enlarge Originally Posted by Autobahn335i Click here to enlarge

        The F82 M4 is plenty fast around the track as is. Word is the Ring time is 7:38. Compare that to the 7:48 of the E92 M3 GTS!

        7.38 is fluffing quick

        Also AWD is to understeer as God is to RWD and some tail end slippy-doo-dah-day (oversteer)
      1. Sticky's Avatar
        Sticky -
        Click here to enlarge Originally Posted by ezec63 Click here to enlarge
        Yupp they havent released much info on it but you can be sure in typical AMG fashion it will be a monster ! Same motor will be in the SLC and capable of almost 600hp which im sure is mostly software so their should be alot of potential in that motor. No doubt the AMG will be the straightline winner with 2 more cylinders and 33% more displacement coupled with AWD and finally a true DCT. They have stated it will deff be lighter than the current c63 but I doubt it will be close to 3300 BMW hit a home run with the curb weight on this car. Honestly im not the biggest fan of AWD sure its good for stoplight races but the control,feel, and excitement of RWD is on another level for me. I had a X6 before my c63 and loved it for a truck if benz doesnt offer RWD on the next C63 or C55 I have a good feeling ill be sitting in a alpine white m4.
        I don't know if it will be mostly software for the SLC as they may be giving the motor a different designation which implies more differences than just a tune: http://www.benzboost.com/content.php...package-option
      1. Sticky's Avatar
        Sticky -
        Click here to enlarge Originally Posted by Autobahn335i Click here to enlarge
        See, surely much less than to, let's say rod bearing issues. It's understandable that BMW does not make this a top priority. Although it surely would be nice. Maybe it will be in the next M1 (if it ever comes) with a proper M race engine.

        The F82 M4 is plenty fast around the track as is. Word is the Ring time is 7:38. Compare that to the 7:48 of the E92 M3 GTS!
        Where did this word come from regarding the ring time?

        If that's accurate it's very impressive.

        Regarding why dry sump is not a priority... well, it should be for any serious track car.
      1. Sticky's Avatar
        Sticky -
        Click here to enlarge Originally Posted by lulz_m3 Click here to enlarge
        I would argue that anything that is high performance must also be high efficiency. You say DI only offers advantages on pump gas, its actually much more advantageous on ethanol as the cooling effect is multiplied vs normal PI of ethanol. Direct injection is not going anywhere, and i'm willing to bet it will trickle its way into race cars over the next 10 years.
        Ok so once again it has been shown that you can have both without direct injection. It isn't some must have to be efficient.

        I said it allows a compression ratio gain on pump gas which is what most people run.

        What does ethanol's cooling effect do for it against say an S65 with more power? It let's you talk about the cooling effect on forums while getting your ass handed to you is what it does.

        Direct injection isn't in race cars now which should tell you plenty. Are there any Formula 1 motors revving to 18k+ with direct injection?
      1. Sticky's Avatar
        Sticky -
        Click here to enlarge Originally Posted by BlackJetE90OC Click here to enlarge
        Actually think the S65 is prone to oil starvation. Some of the failures I have seen first hand at track days have to be related. Just recently saw a DCT M3 with only about 10k miles blow up at COTA. There is a couple turns with extended lateral g's.
        This is why Turner and VAC offer dry sump upgrades. If I tracked seriously my motor would have a dry sump setup no doubt.
      1. Sticky's Avatar
        Sticky -
        Click here to enlarge Originally Posted by Group.america Click here to enlarge

        Also AWD is to understeer as God is to RWD and some tail end slippy-doo-dah-day (oversteer)
        Great point.

        But what if Mercedes offers a rear wheel drive or all wheel drive option like they do on the E63 having all bases covered? Then what?
      1. lulz_m3's Avatar
        lulz_m3 -
        Click here to enlarge Originally Posted by Sticky Click here to enlarge
        The S65 doesn't have Direct injection, so it must be worthless, useless, piece of $#@! technology. Long live the S65.
        If sticky had a bubble above his head, it would look like this^
      1. Group.america's Avatar
        Group.america -
        Click here to enlarge Originally Posted by Sticky Click here to enlarge
        Great point.

        But what if Mercedes offers a rear wheel drive or all wheel drive option like they do on the E63 having all bases covered? Then what?

        I suspect that Rommel and those Panzer tanks would still have their asses handed to them in the deserts of Africa by Patton even if Mercedes offered both options

        Click here to enlarge

        Seriously though the E63 AMG AWD seems to handle better than expected in most videos I have seen... dunno about the C63... personally the little AMG 45 CLA may be more compelling but I will still buy the M4 over the Mercs
      1. Sticky's Avatar
        Sticky -
        Click here to enlarge Originally Posted by Group.america Click here to enlarge
        I suspect that Rommel and those Panzer tanks would still have their asses handed to them in the deserts of Africa by Patton even if Mercedes offered both options

        Click here to enlarge

        Seriously though the E63 AMG AWD seems to handle better than expected in most videos I have seen... dunno about the C63... personally the little AMG 45 CLA may be more compelling but I will still buy the M4 over the Mercs
        Rommel's problem was fuel so maybe if his tanks were direct injected they would have won?

        BMW doesn't seem to have an answer for the 45 AMG's.
      1. ezec63's Avatar
        ezec63 -
        Click here to enlarge Originally Posted by Sticky Click here to enlarge
        I don't know if it will be mostly software for the SLC as they may be giving the motor a different designation which implies more differences than just a tune: http://www.benzboost.com/content.php...package-option
        Yupp just like the M156 and the M159 slight changes probably. Just like a modded M156 makes more power than a stock M159 it should be a fun beast of a motor hopefully they can get the revs up a bit. The m157 is a beast but 6300 is pretty low its just relying on monster torque. The difference between m177 and m178 will probably be minimal (airbox, intake manifold, maybe cams) I doubt theyll go to a bigger turbo size which will be the main factor of how close they will be in terms of power.

        *Edit - Just read your article and makes sense maybe the m177 will be in both c63/55 and base slc than their will be a big $ High perf. version in the top dog SLC. Probably will be a significant hardware difference. Still bet the M177 will be a monster its got a 33% displacement advantage on the S55. Similar to the advantage the m156 has to the S65 its going to be hard to make up without going bigger turbos